Dell PowerEdge SC 430 Instrukcja Użytkownika

Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Introduction Indicators, Messages, and Codes Running the System Diagnostics Trou

Back to Contents Page  Indicators, Messages, and Codes Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Front-Panel Indicato

The front panel also incorporates two USB 2.0 connectors. See Figure2-1.  Diagnostics Indicator Codes The four diagnostic indicator lights on the sy

Figure2-2 shows the back-panel indicators and features. Figure2-3 shows the indicators for the integrated network adapter and Table2-4 details the

System messages appear on the screen to notify you of a possible problem with the system. Table2-5 lists the system messages that can occur and the p

Bad command or file name  Ensure that you have spelled the command correctly, have put spaces in the proper place, and have used the correct pathname

Memory address line failure at address, read value expecting value A memory module might be faulty or improperly seated. Reinstall the memory modules

System Beep Codes If an error that cannot be reported on the screen occurs during POST, the system may emit a series of beeps that identifies the pr

Warning Messages A warning message alerts you to a possible problem and prompts you to respond before the system continues a task. For example, befo

Back to Contents Page  Running the System Diagnostics Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Using Server Administ

Click the testing option in the Main Menu window. Table3-1 provides a brief explanation of testing options. Table 3-1. SystemDiagnosticsTestingOp

Back to Contents Page  Jumpers and Connectors Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Jumpers—A General Explanation

Back to Contents Page  Troubleshooting Your System Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Safety First—For You and

Most PCI devices can share an IRQ with another device, but they cannot use an IRQ simultaneously. To avoid this type of conflict, see the documentatio

3. Swap the faulty keyboard with a working keyboard. If the problem is resolved, replace the faulty keyboard. See "Getting Help."  4. Ent

l Device connected to a USB port is not operating properly.  Action  1. Enter the System Setup program, and ensure that the USB ports are enabled.

 1. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.  2. Press the power button to ground the

The system board can accommodate one processor, five expansion cards (two 5-V, half-length 32-bit, 33-MHz PCI, one 2.5-Gb/sec PCIe [x1], one 2.5-Gb/

Removing and Replacing the Front Drive Bezel Insert  1. To remove the front drive bezel insert, press the two insert tabs on the front drive bezel in

 Action   1. Open the system. See "Opening the System."  2. Ensure that the following components are properly installed: l Expans

4. Enter the System Setup program. If the date and time are not correct in the System Setup program, replace the battery. See "System Battery&q

l Cables inside the system obstruct airflow. l An individual cooling fan has failed. See "Troubleshooting a Fan."  Troubleshooting a Fa

Table A-1.SystemBoardJumperSettings System Board Connectors See FigureA-3 and TableA-2 for the location and description of system board conn

 7. Reseat the memory modules in their sockets. See "Installing a Memory Module" in "Installing System Options."  8. Close th

 12. Remove all expansion cards installed in the system. See "Removing an Expansion Card" in "Installing System Options." 

 8. Close the system. See "Closing the System."  9. Reconnect the system to the electrical outlet, and turn on the system and attache

4. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.  5. Open the system. See "Opening the

 Problem l Diagnostic indicators or system messages indicate a hard drive or expansion card problem l Device driver error. l Hard drive not reco

l Damaged or improperly connected hard-drive cables.  Action   1. Run the appropriate online diagnostic test. See "Using Server Administrato

If the problem persists, go to the next step.  7. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

Back to Contents Page  Installing System Options Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Memory Microprocessor

l System ROM l Advanced Programmable Interrupt Controllers (APIC) l Integrated PCI devices (such as NICs) and SCSI controllers l PCI expansion

 13. When the Memory Info value is correct, press <Esc> to exit the System Setup program.  14. Run the system diagnostics to verify that

Disabling a Forgotten Password The system's software security features include a system password and an admin password, which are discussed in

 5. Open the processor cover by sliding the release lever from under the release level latch on the socket. Then, pull the lever back to release th

 6. Apply new thermal grease to the top of the processor.  7. Place the heat sink assembly back onto the heat sink assembly bracket and tilt the

 6. Place the card-edge connector in the expansion-card connector and press down firmly. Ensure that the card is fully seated in the slot and all car

4. Disconnect the following power-supply cables: l P1 and P2 connector to the system board l P3 and P5 connectors to the SATA drives (if applicab

Cooling Fans The system contains two cooling fans, one for the processor and one for the card cage. Each contains a shroud that is part of the cooli

 5. Remove the battery by pressing on the tab. See Figure5-6. Figure 5-6. Replacing the Battery  6. Install the new battery with the side labe

Back to Contents Page  Installing Drives Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide General Installation Guidelines 

 Configuring the Boot Device The drive or device from which the system boots is determined by the boot order specified in the System Setup program. S

 4. Press in the tabs on each side of the removable drive guide bracket and slide the guide bracket up and out of the drive bay.  5. Close the s

Card" in "Installing System Options."  9. Close the system. See "Closing the System" in "Troubleshooting Your System.

Back to Contents Page  I/O Connectors Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide I/O Connectors Video Connector 

 2. Open the system. See "Opening the System" in "Troubleshooting Your System."  3. Unpack the replacement diskette drive,

16. Test the drive by running the system diagnostics. See "Running the System Diagnostics." Installing 5.25-Inch Optical and Tape Drives

 9. Connect the interface cable from the drive to the IDE connector on the system board to the drive. See Figure6-8 and FigureA-3.  10. Close t

Back to Contents Page  Service Only Parts Replacement Procedures Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Before You

 Replacing the Bezel  1. Align the bezel with the chassis frame and slide it down into position.  2. Attach the three bezel release screws to

 Replacing the I/O Panel   1. If system is powered on, turn off the system and attached peripherals, and disconnect the system from the electric

1. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.  2. Open the system. See "Opening the

l If applicable, diskette data cable from the FLOPPY connector l I/O panel cable from the FRONT PANEL connector l 5.25-inch device data cable fr

 7. Connect the following cables that you removed in "Removing the System Board." See FigureA-3. l Two power-supply cables to the POWE

Back to Contents Page  Getting Help Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Technical Assistance Dell Enterprise

USB Connector The system's USB connector supports USB-compliant peripherals such as keyboards, mice, and printers and may also support USB-comp

support.jp.dell.com (Japan only) support.euro.dell.com (Europe only) l Electronic Quote Service [email protected] [email protected] (Asian/Pacific c

the system diagnostics.  4. Include any accessories that belong with the item(s) being returned (such as power cables, media such as CDs and diske

determining which codes to use, contact a local or an international operator.  Country (City) International Access Code Country Code City Code Depart

Country Code: 673 Customer Service (Penang, Malaysia) 6046334949 Transaction Sales (Penang, Malaysia) 6046334955 Canada (North York, Ontario) Inte

Switchboard (Home/Small Business) 32875000 Switchboard Fax (Home/Small Business) 32875001 Dominica General Support toll-free:1-866-278-6821 Dominic

Medium Business Division 34160912 Home and Small Business Division 29693105 India Technical Support 1600338045 Sales (Large Corporate Accounts) 16

Latin America Customer Service (Austin, Texas, U.S.A.) 512728-3619 Fax (Technical Support and Customer Service) (Austin, Texas, U.S.A.) 512728-3883

International Access Code: 00 Country Code: 47 Relational Customer Care 67117575 Home/Small Business Customer Care 23162298 Switchboard 67116800 Fax

Customer Care 902115236 Switchboard 917229200 Fax 917229583 Sweden (Upplands Vasby) International Access Code: 00 Country Code: 46 City Code:

Back to Contents Page  U.S.A. (Austin, Texas) International Access Code: 011 Country Code: 1 (1-877-335-5638) Employee Purchase Program (EPP) Custome

Network Cable Requirements The NIC supports a UTP Ethernet cable equipped with a standard RJ45-compatible plug. Observe the following cabling restri

Back to Contents Page Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Notes, Notices, and Cautions Abbreviations and Acronym

Back to Contents Page  Introduction Dell™PowerEdge™SC430SystemsInstallationandTroubleshootingGuide Other Information You May Need The fo