Dell PowerVault NX3600 Instrukcja Użytkownika

Dell FluidFS NAS SolutionsOwner's ManualRegulatory Model: E02T and C11MRegulatory Type: E02T001 and C11M001

Figure 6. fibre Channel Indicators1. Amber LED (2 Gbps)2. Green LED (4 Gbps) 3. Yellow LED (8 Gbps)Indicator DescriptionAll LEDs off Indicates that th

Power Indicator CodesPower Supply Unit LED Indicator CodesEach AC power supply has an LED that serves as an indicator to show whether power is present

Indicator DescriptionNOTE: The LED flashes once every two seconds.If the controller is not responding, it may indicate that the operating system did n

Power LED Indicator CodesIndicator DescriptionOff Indicates that no power is available to the fan.Solid green Indicates that the power is on.Status LE

• For the full name of an abbreviation or acronym used in this document, see the Glossary at support.dell.com/manuals.NOTE: Always check for updates o

2Installing System ComponentsRecommended ToolsYou may need the following items to perform the procedures in this section:• Key to the system keylock•

4. front bezel5. locking hookRemoving The Front Bezel1. Unlock the keylock at the left end of the bezel.2. Lift the release latch next to the keylock.

Figure 10. Removing and Installing a Controller From the NAS Appliance1. controller slot in the NAS appliance2. controller3. controller handle4. relea

8. Log on to the NAS Manager and select Cluster Management → Hardware → Controllers Management.9. Select the controller you want to attach.10. Click A

Figure 11. Removing and Installing an AC Power Supply1. power supply2. release latch3. cable securing strap4. power supply handle5. power supply unit

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

NOTE: When installing or hot-swapping a new power supply, allow several seconds for the system to recognize the power supply and determine its status.

Figure 12. Opening and Closing the Cooling Fan Access Door1. cooling fan release latch2. cooling fan access door3. Press the fan release tabs (2) and

Figure 13. Removing and Installing a Cooling Fan1. fan release tabs (2)2. cooling fans (6)3. cooling-fan connectors (6)Installing A Cooling FanCAUTION

WARNING: Opening or removing the NAS appliance cover when the system is on may expose you to a risk of electric shock.WARNING: This NAS appliance shou

Figure 14. Opening and Closing the NAS Appliance1. screws (4)2. NAS appliance coverClosing The NAS ApplianceNOTE: This is a service only procedure.1.

Figure 15. Inside the NAS Appliance1. NAS appliance2. controllers (2)3. power supply units (2)4. power transmission boards (2)5. information tag6. coo

CAUTION: Label all the cables correctly before disconnecting any cables. Ensure that the cables are reconnected to the same ports when installing the

Installing The Front LED Status ModuleWARNING: Whenever you need to lift the NAS appliance, get others to assist you. To avoid injury, do not attempt

CAUTION: Label all the cables correctly before disconnecting any cables. Ensure that the cables are reconnected to the same ports when installing the

Installing The Power Transmission Board AssemblyWARNING: Whenever you need to lift the NAS appliance, get others to assist you. To avoid injury, do no

ContentsNotes, Cautions, and Warnings...21 About Your

3. Disconnect all the cables connected to the back of the NAS appliance.4. Remove the controllers from the NAS appliance.5. Remove the NAS appliance f

The notches on the floor of the chassis hold the midplane board in place.4. Using the Torx 15 screwdriver, replace the 11 screws to secure the midplan

Figure 19. Opening and Closing the Controller1. release button2. controller coverClosing The ControllerCAUTION: Many repairs may only be done by a cer

Figure 20. Inside the Controller1. controller2. backup power supply3. Internal USB port4. expansion-card riser cage5. hard-drive assembly6. memory mod

Figure 21. Removing and Installing the Expansion Card Riser1. expansion-card riser cage2. screws (2)3. riser guide on controller chassis side wall (ri

Figure 22. Removing and Installing the Expansion-Card Holder1. release latch2. card holder3. expansion-card cage4. notch6. Using a #2 Philips screwdri

Figure 23. Removing and Installing the Expansion Card1. expansion card2. expansion-card cage3. expansion-card latchInstalling The Expansion-Card Riser

8. Using the #2 Philips screwdriver, tighten the two captive screws that secure the expansion-card riser cage to the controller chassis.9. Close the c

38

3Troubleshooting Your SystemSafety First—For You And Your SystemCAUTION: Many repairs may only be done by a certified service technician. You should o

Installing The Front LED Status Module...27Pow

If the problem persists, see Getting Help.40

4Using System DiagnosticsIf you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance. The

System Diagnostic ControlsMenu DescriptionConfiguration Displays the configuration and status information of all detected devices.Results Displays the

5Technical SpecificationsNOTE: The following specifications apply to each controller.ProcessorProcessor type One or two Intel Xeon processors E5-5600

VideoVideo type Integrated Matrox G200Video memory 16 MB sharedEnvironmentalNOTE: For additional information about environmental measurements for spec

EnvironmentalStorage –305 m to 12192 m (–1000 ft to 40,000 ft)Airborne Contaminant LevelClass G1 as defined by ISA-S71.04-198545

46

6Getting HelpContacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing

1About Your SystemFront-Panel Features And IndicatorsFigure 1. Front Bezel IndicatorsFigure 2. Front-Panel Features and Indicators5

Item Indicator, Button, or ConnectorIcon Description1 System identification button The identification buttons on the front and back panels can be used

Item Indicator, Button, or ConnectorIcon Description3 Release button Press the release button to disengage the controller handle and remove the storag

Item Indicator, Button, or ConnectorIcon Description14 Service action button Used to troubleshoot certain errors. This button can be pressed using the

SFP+ IndicatorsFigure 5. SFP+ Indicators1. link indicator2. activity indicatorIndicator DescriptionLink and activity indicators are off The SFP+ modul