Dell Dimension 2200 Instrukcja Użytkownika

Dell™Dimension™2200 Technical Overview Controls and Lights Solving Problems System Codes and Messages Technical Specifications System Setup Program

5. While facing the front of the computer, press in the front-panel release tab at the top of the computer.  6. Swing the front panel away from

7. Rotate the insert toward you, and remove it from the front panel. If you permanently remove a drive from the drive cage, replace the front-pan

10. Slide the drive assembly into the drive bay. 11. If you are installing a controller card, configure and install it in a connector slot now.

14. Replace the front panel. 15. Make sure that no cable connections were loosened during the procedure. Arrange cables so that they will not in

10. Remove the rails from each side of the existing drive, and install them on each side of the new drive. 11. Slide the drive assembly into the d

18. See the drive's documentation for instructions on installing any software required for drive operation. Hard Drive 1. Shut down the compu

10. See the drive's documentation for instructions on installing any software required for drive operation. Power Supply and Fan Assembly 1. 

3. Disconnect the computer power cable from the wall outlet, and then press the power button to ground the system board. 4. Remove the computer co

7. Align the cutout on the bottom of the card with the crossbar in the system board connector. Gently rock the card into the connector until it is

13. Install any drivers required for the card as described in the card documentation. Removing Cards 1. Shut down the computer. 2. Turn off an

Back to Contents Page System Codes and Messages Dell™Dimension™2200 Diagnostic Codes POST Beep Codes System Messages Diagnostic Codes Your

8. Align the notches on the bottom of the module with the crossbars in the connector. 9. Insert the module straight down into the connector, mak

 9. Rotate the power supply back into place. 10. Replace the computer cover. 11. Plug your computer and devices into their electrical outlet

10. Remove the chip from the socket. Leave the release lever extended so that the socket is ready for the new microprocessor. 11. Unpack the new

c. Press down on the top of the fan to snap the clip over the tab on the bottom edge of the microprocessor socket. d. Connect the fan to the syste

13. Carefully lift the system board out of the I/O gasket and remove the board from the computer. The I/O gasket is on the back of the computer where

Back to Contents Page Solving Problems Dell™Dimension™2200 Accessing Help Files Power Problems Start-Up Error Messages Accessing Help Files

Video and Monitor Problems If the screen is blank If the screen is difficult to read Sound and Speaker Problems Insert bootable media— The operat

Printer Problems If you cannot print to a parallel port printer If you cannot print to a USB printer Run the speaker diagnostics— Some speaker sys

Scanner Problems Modem Problems Mouse Problems HINT: If you need technical assistance for your scanner, call the scanner's manufacturer. Dell

Keyboard Problems Drive Problems If you cannot save a file to a floppy disk  If you cannot play a music CD or install a program from a CD If y

POST Beep Codes If the monitor cannot display errors or problems, during POST the computer might emit a series of beeps, or beep code, that identifies

If the CD-RW drive stops writing If you have a hard drive problem Network Problems Microsoft®Windows®Error Messages Adjust the Windows volume

General Program Problems A program crashes A program stops responding A program error causes the system to lock up A solid blue screen appears

E-Mail Problems Resolving Other Technical Problems Reinstalling Drivers A driver is a software program that allows a hardware device controller to f

attempt to return your operating system to its previous operating state before the new device driver installation: 1. Click the Start button, and the

Using System Restore Windows XP provides a System Restore feature that allows you to return your computer to an earlier operating state if changes to

5. Click Next. The Restoration Complete screen appears after System Restore completes collecting data, and then the computer automatically restarts

14. If you have a network card in your computer, select the appropriate network settings. If you do not have a network card, this option does not ap

Back to Contents Page Technical Specifications Dell™Dimension™2200      MicroprocessorVideoSystem InformationAudioExpansion Bus

      Mouse 6-pin mini-DIN connector or USB connector USB four USB-compliant connectors Audio1 three miniature connectors for line-in, line-out,

Back to Contents Page   

Back to Contents Page    CH-2 Timer Error An error is occurring on the timer on the system board. See "Contacting Dell" in the Owner&apos

Back to Contents Page System Setup Program Dell™Dimension™2200 Overview Viewing Settings Clearing Forgotten Passwords Overview The system s

l Computer data – Two boxes below the title that display the system processor, L2 cache, service tag, and the version number of the system setup progr

The following table shows System Security option information. Clearing Forgotten Passwords If you forget your system or setup password, you cannot op

Back to Contents Page Technical Overview Dell™Dimension™2200 Internal View System Board Connectors and Sockets Power Supply DC Power Conne

Power Supply The 145-W power supply can operate from an AC power source of 115 VAC at 60 Hz or 230 VAC at 50 Hz. The power supply provides the DC op

DC Power Connector P1  DC Power Connector P3 Pin Number Signal name 18-AWG Wire 1 +3.3 VDC Orange 2 +3.3 VDC Orange 3 COM Black 4 +5 VDC Red 5

 DC Power Connectors P4, P5, and P6  Back to Contents Page    Pin Number Signal Name 22-AWG Wire 1 +5 VDC Red 2 COM Black 3 COM Black 4 +12

Back to Contents Page Controls and Lights Dell™Dimension™2200 Front View Back View Front View  CD Activity Light The CD activity light is o

5. Uncheck the Enable digital CD audio for this CD-ROM device box. Back View  Power Connector Plug one end of your computer power cable into the

Serial Connector Connect a serial device, like a handheld device, to the serial connector. Voltage Selection Switch See "Safety Instructions"

Back to Contents Page Documentation Dell™Dimension™2200 Printed Documentation Online Documentation Printed Documentation To save PDF files (

Back to Contents Page Adding and Replacing Parts Dell™Dimension™2200  Safety Instructions As you use your computer, observe the following safe-ha

1. Turn off your computer and all devices. 2. Ground yourself by touching an unpainted metal surface at the back of the computer before touching a

3. Disconnect the computer power cable from the wall outlet, and then press the power button to ground the system board. 4. Open the cover: a. 

1. Shut down the computer. 2. Turn off any attached devices and disconnect them from their electrical outlets. 3. Disconnect the computer power