Dell P2214H Podręcznik Użytkownika

User’s Guide Dell P2214H Dell P2414H Model No.: P2214H / P2414H Regulatory model: P2214Hb / P2214Hb

6 USB downstream port Connect your USB device. You can only use this connector after you have connected the USB cable to the

Resolution Specifications Model P2214H P2414H Horizontal scan range 30 kHz to 83 kHz (automatic) 30 kHz to 83 kHz (automatic) V

Electrical Specifications Model P2214H/P2414H Video input signals • Analog RGB, 0.7 Volts +/- 5%, positive polarity at 75 ohm i

Depth 180.0 mm (7.09 inches) 180.0 mm (7.09 inches) Dimensions (without stand) Height 304.4 mm (11.98 inches) 335.1 mm (13.19 inch

Non-operating 12,192m (40,000 ft) (maximum) Thermal dissipation • 102.3 BTU/hour (maximum) • 62.8 BTU/hour (typical) Po

* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor. ** Maximum power consumption with ma

DVI Connector Pin Number 24-pin Side of the Connected Signal Cable 1 TMDS RX2-2 TMDS RX2+ 3 TMDS Ground 4 Floating 5 Floating 6 DDC Clock 7 DDC Dat

DisplayPort Connector Pin Number 20-pin Side of the Connected Signal Cable 1 ML0(p) 2 GND 3 ML0(n) 4 ML1(p) 5 GND 6 ML1(n) 7 ML2(p) 8 GND 9 M

Universal Serial Bus (USB) Interface This section gives you information about the USB ports that are available on the monitor. NOTE: This moni

USB Downstream Connector Pin Number 4-pin Side of the Connector 1 VCC 2 DMD 3 DPD 4 GND USB Ports • 1 upstream - back • 4 downs

____________________ Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of you

• Use a lightly-dampened, warm cloth to clean the monitor. Avoid using detergent of any kind as some detergents leave a milky film on the

2 Setting Up the Monitor Attaching the Stand NOTE: The stand is detached when the monitor is shipped from the factory. NOTE: This is

Connecting the blue VGA cable Connecting the white DVI cable Connecting the black DisplayPort cable CAUTION: The graphics are used for the purpos

Connecting the USB cable After you have completed connecting the VGA/DVI/DP cable, follow the procedures below to connect the USB cable to t

Attaching the Cable Cover The Cable Cover is detached when the monitor is shipped from the factory. 1. Fit the two tabs on the

Wall Mounting (Optional) (Screw dimension: M4 x 10 mm). Refer to the instructions that come with the VESA-compatible wall mounting kit.

26 | Setting Up the Monitor

3 Operating the Monitor Power On the Monitor Press the button to turn on the monitor. Using the Front Panel Controls Use the control buttons on

2 3 4 5 1 Use this button to directly access the Brightness/Contrast menu. Shortcut key/ Brightness/ Contrast Use the MENU button to launch

3 Use the OK button to confirm your selection. OK 4 Use the Back button to go back to the previous menu. Back Using the On-Screen Display

Contents 1 About Your Monitor . . . . . . . . . . . . . . . . . . . . . . 5 Package Contents . . . . . . . . . . . . .

Main Menu for digital (DVI) input or Main Menu for digital (DP) input NOTE: Auto Adjust is only available when you use the analog (VG

5. Press to enter the slide bar and then use the and buttons, according to the indicators on the menu, to make your changes. 6. Select the

Icon Menu and Description Submenus Brightness/ Use this menu to activate Brightness/Contrast adjustment. Contrast Brightne

Input Source Use the Input Source menu to select between the different video signals that may be connected to your monitor. Auto Select Press so

Color Use Color Settings to adjust the color setting mode. Settings Input Color Allows you to set the video input mode to: Format RGB: Select this

Preset Modes When you select Preset Modes, you can choose Standard, Multimedia, Movie, Game, Text, Warm, Cool or Custom Color f

Image Makes upsized images higher quality by removing image fading and Enhance roughness of edge. NOTE: Image Enhance is avail

Energy Settings Energy Smart To turn on or off dynamic dimming. The dynamic dimming feature automatically reduces the screen's brightn

Menu Select this option to adjust the settings of the OSD, such as, the Settings languages of the OSD, the amount of time the menu re

Other Settings DDC/CI DDC/CI (Display Data Channel/Command Interface) allows your monitor parameters (brightness, color balance, and etc.)

5 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 FCC Notices (U.S. Only) and Other Regulatory Information . . .

LCD Helps reduce minor cases of image retention. Depending on the Conditioning degree of image retention, the program may take some time to r

OSD Warning Messages When the Energy Smart or Dynamic Contrast feature is enabled (in these preset modes: Game or Movie), the manual bright

When the monitor enters the Power Save mode, the following message appears: Activate the computer and wake up the monitor to gain access to t

or See Troubleshooting for more information. Setting the Maximum Resolution To set the maximum resolution for the monitor: Windows® 7 or Wind

Using the Tilt, Swivel, and Vertical Extension NOTE: This is applicable for a monitor with a stand. When any other stand is bought, ple

Rotating the Monitor Before you rotate the monitor, your monitor should be fully vertically extended (Vertical Extension) and fully tilted up

Adjusting the Rotation Display Settings of Your System After you have rotated your monitor, you need to complete the procedure below to adj

4 Troubleshooting WARNING: Before you begin any of the procedures in this section, follow the Safety Instructions. Self-Test Your monitor

or 4. This box also appears during normal system operation, if the video cable becomes disconnected or damaged. 5. Turn off your monitor

3. Press and hold Button 1 and Button 4 on the side panel simultaneously for 2 seconds. A gray screen appears. 4. Care

1 About Your Monitor Package Contents Your monitor ships with the components shown below. Ensure that you have received all the com

Missing Pixels LCD screen has • Cycle power on-off. spots • Pixel that is permanently off is a natural defect that can occu

Missing Color Picture missing • Perform monitor self-test feature check. color • Ensure that the video cable conn

Universal Serial Bus (USB) Specific Problems Specific What You Possible Solutions Symptoms Experience USB interface is USB peripherals • C

5 Appendix WARNING: Safety Instructions WARNING: Use of controls, adjustments, or procedures other than those specified in this

1. For Windows® 8 only, select the Desktop tile to switch to classic desktop. 2. Right-click on the desktop and click Screen Resoluti

• Power Cable (Varies by Countries) • VGA Cable • DP Cable • USB Upstream Cable • Drivers and Documentation Media • Quick Set

• On-Screen Display (OSD) adjustments for ease of set-up and screen optimization. • Software and documentation media includes an Informa

Back View Back View with monitor stand Label Description Use 1 VESA mounting holes (100 mm x 100 mm - behind attached VESA Cover) Wall moun

Side View Bottom View Bottom view without monitor stand Label Description Use 1 AC power cord connector Connect the power cable. 2 DP c