Dell PowerEdge M IO Aggregator Instrukcja Właściciela Strona 227
- Strona / 258
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Storm Control | 225
22
Storm Control
Overview
The Dell Force10 operating software (FTOS) storm control feature allows users to limit or suppress
traffic during a traffic storm.
Storm Control Commands
The storm control commands are:
• io-aggregator broadcast storm-control
• show io-aggregator broadcast storm-control status
io-aggregator broadcast storm-control
Rate-limit the broadcast traffic to 1 Gbps.
Syntax
io-aggregator broadcast storm-control
To disable storm control, use the no io-aggregator broadcast storm-control command.
Defaults
Enabled
Command Modes
CONFIGURATION
Command
History
show io-aggregator broadcast storm-control status
Shows if storm control is enabled or disabled. If enabled, displays information on the rate limit value.
Syntax
show io-aggregator broadcast storm-control status
Command Modes
EXEC Privilege
Note: When iSCSI storage devices are detected on the server-ports, storm-control is disabled
on the those ports. When the iSCSI devices are off the ports, storm-control is enabled again.
Version 8.3.17.0 Supported on M I/O Aggregator
- Notes, Cautions, and Warnings 2
- About this Guide 7
- Related Documents 8
- Before You Start 9
- DCB Support 10
- FCoE Connectivity 10
- Link Aggregation 11
- Link Tracking 11
- Where to Go From Here 12
- Before You Start 13
- 12 14
- CLI Basics 15
- Multiple Configuration Users 16
- Obtaining Help 17
- Combination Action 18
- Using the Keyword no 19
- Filtering show Commands 19
- Command Modes 20
- INTERFACE Mode 21
- LINE Mode 21
- MONITOR SESSION Mode 21
- PROTOCOL LLDP Mode 22
- File Management 23
- 27
- url url 30
- 36 38
- Control and Monitoring 39
- FTOS#configure 40
- FTOS(conf)# 40
- 54 56
- FTOS#show memory stack-unit 0 57
- Control and Monitoring 59
- Important Points to Remember 62
- Control and Monitoring 65
- [stack-unit unit-id 68
- Control and Monitoring 69
- Examples 69
- system component status 71
- 76 78
- BOOT_USER # 80
- 86 88
- Data Center Bridging 89
- 90 92
- Data Center Bridging 93
- FTOS# show dcb 95
- DCB Status : Enabled 95
- 96 98
- Data Center Bridging 99
- Field Description 100
- EXEC Privilege 101
- 104 106
- Overview 107
- DHCP Client Commands 107
- FIP Snooping 113
- FTOS#show fip-snooping config 114
- Global FC-MAP Value: 0X0EFC00 114
- FTOS# show fip-snooping enode 115
- FTOS# show fip-snooping fcf 116
- FIP Snooping 119
- IGMP Commands 121
- TenGigabitEthernet 124
- Interfaces 127
- Port Channel Commands 128
- Virtual LAN (VLAN) Commands 129
- FTOS(conf-po-failover-grp)# 132
- FTOS(conf)#int vlan 3 136
- FTOS(conf-if-vl-3)# 136
- FTOS(conf-lldp)#show conf 142
- FTOS(conf-lldp)# 142
- Line Description 144
- [interface] description 146
- FTOS#show int po 1 brief 149
- Codes: L - LACP Port-channel 149
- unit-id ] 151
- Items Description 152
- OK Status: Terminated 153
- G = GVRP VLAN 154
- P = primary VLAN 154
- C = community VLAN 154
- I = isolated VLAN 154
- Column Heading Description 155
- 158 160
- IPv4 Routing 161
- Lines Description 170
- • too short 174
- 174 176
- 178 180
- LACP Commands 181
- Layer 2 185
- 186 188
- LLDP Commands 189
- Port Monitoring 193
- Port Monitoring 197
- Commands 197
- FTOS(conf-mon-sess-11)# 198
- Quality of Service (QoS) 199
- Security 201
- port-number 206
- {1 206
- 206 208
- SNMP Commands 209
- Syslog Commands 209
- [facility-type] 212
- CONFIGURATION 212
- Example 1 217
- Example 2 217
- Disabled 219
- Stacking Commands 221
- 0-5 hard 222
- [stack 226
- Storm Control 227
- Storm-Control Enabled 228
- System Time 229
- FTOS#show calendar 230
- Enter one of the following: 235
- 234 236
- UFD Commands 237
- Debugging and Diagnostics 241
- Example 3 246
- 0-0 [port 248
- 0-0 {counters 248
- Example 4 249
- Example 250
- Example 7 251
- Example 8 251
- 0-5 port-set 0-0 [counters] 253
- Message Types 257
Powiązane produkty i podręczniki dla Serwery Dell PowerEdge M IO Aggregator
Serwery Dell PowerEdge R200 Instrukcja Właściciela
(182 strony)
(182 strony)
Serwery Dell PowerEdge R610 Instrukcja Właściciela
(184 strony)
(184 strony)
Serwery Dell 1955 Instrukcja Użytkownika
(12 strony)
(12 strony)
Serwery Dell 8/8 Informacje Techniczne
(147 strony)
(147 strony)
Serwery Dell PowerEdge BMX01 Instrukcja Właściciela
(108 strony)
(108 strony)
Serwery Dell PowerEdge NM176 Podręcznik Użytkownika
(292 strony)
(292 strony)
Serwery Dell PowerEdge VRTX Instrukcja Właściciela
(150 strony)
(150 strony)
Serwery Dell PowerEdge NM176 Instrukcja Właściciela
(454 strony)
(454 strony)
Serwery Dell 800 Instrukcja Obsługi
(75 strony)
(75 strony)
Serwery Dell POWEREDGE R710 Dokumentacja
(63 strony)
(63 strony)
Serwery Dell DAE Instrukcja Użytkownika
(16 strony)
(16 strony)
Serwery Dell PowerVault 3000i Dokumentacja
(32 strony)
(32 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji