Dell PowerVault DP100 Instrukcja Użytkownika Pobierz pdf (Strona 9)

number.

problem persists, see Getting

Help.

Plug & Play Configuration

Error

Error encountered in

initializing PCI device; faulty

system board.

Install the NVRAM_CLR jumper

and reboot the system. See

Figure6-1 for jumper location.

Check for a BIOS update. If

the problem persists, see

Troubleshooting Expansion

Cards. If the problem persists,

see Getting Help.

Primary drive n

configuration error

Primary drive 1 failure



Faulty hard-disk drive.

Replace the hard-disk drive.

See Troubleshooting SATA

Hard Drives or

Troubleshooting

a SAS RAID Controller in for

the appropriate drive(s)

installed in your system.

Read fault

Requested sector not found

Faulty diskette, diskette

drive, optical drive, or hard

drive.

Replace the diskette. Ensure

that the diskette, optical, and

hard-drive cables are properly

connected. See

Troubleshooting a Diskette

Drive, Troubleshooting an

Optical Drive, Troubleshooting

SATA Hard Drives," or

Troubleshooting a SAS RAID

Controller" for the appropriate

drive(s) installed in your

system.

Remote Configuration update

attempt failed

System could not implement

Remote Configuration

request.

Retry Remote Configuration.

ROM bad checksum = address

Faulty or improperly installed

expansion card.

Remove and reseat the

expansion cards. See

Troubleshooting Expansion

Cards.

SATA Port n

hard disk drive

configuration error

SATA Port n

hard disk drive

failure

SATA Port n

hard disk drive

auto-sensing error



Faulty SATA hard drive.

Replace the hard-disk drive.

See Troubleshooting SATA

Hard Drives for the

appropriate drive(s) installed

in your system.

SATA Port n hard disk not

found

SATA hard drive not

connected to port n.

Ensure that the hard-drive

cable is properly connected.

See Hard Drives.

If a drive is not connected to

port n, check that the SATA

port is disabled in the System

Setup program. See Using the

System Setup Program.

Sector not found

Seek error

Seek operation failed



Faulty diskette or hard drive.

Replace the diskette. If the

problem persists, see

Troubleshooting SATA Hard

Drives or Troubleshooting

SATA Hard Drives for the

appropriate drive installed in

your system.

Shutdown failure

Shutdown test failure.

Ensure that all memory

modules are properly installed.

See Troubleshooting System

Memory. If the problem

persists, see Getting Help.

The amount of system

memory has changed.

Faulty memory module.

See Troubleshooting System

Memory. If the problem

persists, see Getting Help.

The amount of tested memory

is below the minimum system

configuration. System halted!

Invalid memory configuration

See Memory.

Faulty memory module.

See Troubleshooting System

Memory. If the problem

persists, see Getting Help.

Time-of-day clock stopped

Faulty battery; faulty system

board.

See Troubleshooting the

System Battery. If the problem

persists, see Getting Help.

Time-of-day not set - please

run SETUP program

Incorrect Time or Date

settings; faulty system

battery.

Check the Time and Date

settings. See "Using the

System Setup Program" in

your User's Guide. If the

problem persists, see

Troubleshooting the System

Battery.

Timer chip counter 2 failed

Faulty system board.

See Getting Help.

Unexpected interrupt in

protected mode

Faulty or improperly installed

memory modules or faulty

system board.

Ensure that all memory

modules are properly installed.

See Memory. If the problem

persists, see Troubleshooting

System Memory

. If the problem

persists, see Getting Help.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 87 88

Komentarze do niniejszej Instrukcji

Brak uwag