Dell PowerEdge 2850 Instrukcja Naprawy Pobierz pdf (Strona 17)

range.

board (see "Installing Drives"). If the problem persists, see

"Troubleshooting Power Supplies" in "Troubleshooting Your System."

E0212

VOLT BP 3.3

E0212

VOLT BP 5

E0212

VOLT CPU VRM

Microprocessor VRM voltage is out of acceptable

range; faulty or improperly installed microprocessor

VRM; faulty system board.

This message is not applicable to this system.

E0212

VOLT NIC 1.8V

Integrated NIC voltage is out of acceptable range;

faulty or improperly installed power supply; faulty

system board.

See "Troubleshooting Power Supplies" in "Troubleshooting Your System."

E0212

VOLT NIC 2.5V

E0212

VOLT PLANAR

REG

System board is out of acceptable voltage range;

faulty or improperly installed system board.

E0276

CPU VRM n

Specified microprocessor VRM is faulty,

unsupported, improperly installed, or missing.

These messages are not applicable to this system.

E0276

MISMATCH VRM

E0280

MISSING VRM n

E0319

PCI OVER

CURRENT

Faulty or improperly installed expansion card.

See "Troubleshooting Expansion Cards" in "Troubleshooting Your System."

E0412

RPM FAN n

Specified cooling fan is faulty, improperly installed,

or missing.

See "Troubleshooting a Fan" in "Troubleshooting Your System."

E0780

MISSING CPU 1

Microprocessor is not installed in socket PROC_1.

Install a microprocessor in socket PROC_1 (see "Processors" in "Installing

System Options"). To identify microprocessor socket PROC_1, see FigureA-

E07F0

CPU IERR

Faulty or improperly installed microprocessor.

See "Troubleshooting the Microprocessors" in "Troubleshooting Your

System."

E07F1

TEMP CPU n

HOT

Specified microprocessor is out of acceptable

temperature range and has halted operation.

See "Troubleshooting System Cooling Problems" in "Troubleshooting Your

System." If the problem persists, ensure that the microprocessor heat sinks

are properly installed (see "Processors" in "Installing System Options").

E07F4

POST CACHE

Faulty or improperly installed microprocessor.

See "Troubleshooting the Microprocessors" in "Troubleshooting Your

System."

E07F4

POST CPU REG

E07F4

POST CPU SMI

SMI handler failed to initialize; faulty system board.

See "Getting Help."

E07FA

TEMP CPU n

THERM

Specified microprocessor is out of acceptable

temperature range and is operating at a reduced

speed, or frequency.

See "Troubleshooting System Cooling Problems" in "Troubleshooting Your

System." If the problem persists, ensure that the microprocessor heat sinks

are properly installed (see "Processors" in "Installing System Options").

E0876

POWER PS n

No power available from the specified power

supply; specified power supply is improperly

installed or faulty.

See "Troubleshooting Power Supplies" in "Troubleshooting Your System."

E0880

INSUFFICIENT

Insufficient power is being supplied to the system;

power supplies are improperly installed, faulty, or

missing.

See "Troubleshooting Power Supplies" in "Troubleshooting Your System."

E0CB2

MEM SPARE ROW

Correctable errors threshold was met in a memory

bank: errors were remapped to the spare row.

See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0CF1

MBE DIMM Bank

Memory modules installed in the specified bank are

not the same type and size; faulty memory module

(s).

Ensure that all banks contain memory modules of the same type and size

and that they are properly installed. If the problem persists, see

"Troubleshooting System Memory" in "Troubleshooting Your System."

E0CF1

POST MEM 64K

Parityfailureinthefirst64KBofmainmemory.

See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0CF1

POST NO

MEMORY

Main-memory refresh verification failure.

Ensure that all banks contain memory modules of the same type and size

and that they are properly installed. If the problem persists, see

"Troubleshooting System Memory" in "Troubleshooting Your System."

E0CF5

LOG DISABLE

SBE

Multiple single-bit errors on a single memory

module.

See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0D76

DRIVE FAIL

Faulty or improperly installed hard drive or RAID

controller.

See "Troubleshooting SCSI Hard Drives" and "Troubleshooting a RAID

Controller Card" in "Troubleshooting Your System."

E0F04

POST CMOS

CMOS write/read failure; faulty system board.

See "Getting Help."

E0F04

POST CPU

SPEED

Microprocessor speed control sequence failure.

See "Getting Help."

E0F04

POST DMA INIT

DMA initialization failure; DMA page register

write/read failure.

See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0F04

POST DMA REG

Faulty system board.

See "Getting Help."

E0F04

POST KYB

CNTRL

Faulty keyboard controller; faulty system board.

See "Getting Help."

E0F04

POST MEM RFSH

Main-memory refresh verification failure.

See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0F04

POST PIC REG

Master or slave PIC register test failure.

See "Getting Help."

E0F04

POST SHADOW

BIOS-shadowing failure.

See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0F04

POST SHD TEST

Shutdown test failure.

E0F04

POST SIO

Super I/O chip failure; faulty system board.

See "Getting Help."

E0F04

POST TIMER

Programmable interval timer test failure; faulty

system board.

See "Getting Help."

E0F0B

POST ROM

CHKSUM

Faulty or improperly installed expansion card.

See "Troubleshooting Expansion Cards" in "Troubleshooting Your System."

E0F0C

VID MATCH CPU

Specified microprocessor is faulty, unsupported,

improperly installed, or missing.

See "Troubleshooting the Microprocessors" in "Troubleshooting Your

System."

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 75 76

Komentarze do niniejszej Instrukcji

Brak uwag

Dell PowerEdge 2850 Instrukcja Naprawy Strona 17

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Serwery Dell PowerEdge 2850